TigerDirect

Popular Posts

  • Canon iP100 Reset Procedure
    When the error or pop-up message appears on your screen “ink absorber is full”. Your printer needs to reset.  Here’s how to fix it! Hardwa...
  • Canon printer Error Code 6502
    Error Code 6502 appears mostly after changing the cartridge. Option 1 Unplug the printer Remove the faulty Cartridge Plug in the...
  • Samsung ML-1660 Reset
    Now I have not gotten any Samsung ML-1660, but I have method to reset page counter Samsung ML 1660 for you. So that, you must to do this wit...
  • Waste Ink Tank Almost Full Canon iP6220D
    The message Waste ink tank almost full or the error5b00 appears on Canon Pixma iP6220D and Canon Pixma iP6210D. Just reset the was waste in...
  • Canon iP4680 Resetter
    This is the manual guide of resetting the Canon iP4680 printer. The indication of problem  is  lights blinking on the POWER and RESUME bu...
  • Canon Pixma MP110 ink absorber
    The waste ink absorber on Canon Pixma mp110 The waste Ink absorber is a small, deep sponge, located where the cartridges rest when the p...
  • Canon Ip1300 Reset
    Reset Canon Ip1300 The Canon Printer Pixma iP1xxx Series is  high quality photo printer at an affordable price. Print borderless photos ...
  • Brother DCP-6690CW Reset Factory Settings
    This guide is to reset into factory defaults of the following model Brother DCP-6690CW. Follow the steps below: Make sure the machine ...
  • Samsung SCX-4300 Reset
    The SAMSUNG SCX-4300 is small, yet powerful. Despite its diminutive 16.00″ x 14.25″ x 9.10″ dimensions, it cranks out 600 x 600 dpi docum...
  • Samsung ML-1640
    Samsung ML-1640, a compact and cheep price and suitable for home and small office, has a starter Toner Cartridge can print maximum about 700...
Powered by Blogger.

Previous Post

Monday, March 4, 2013

Canon printer Error Code 6502


Printer


Error Code 6502 appears mostly after changing the cartridge.

Option 1

  • Unplug the printer
  • Remove the faulty Cartridge
  • Plug in the printer and press and hold power button
  • Keep it held down. 
  • Press Resume twice, and this should reset the fault.

Option 2


  • The last cartridge installed may be faulty
  • Install a new cartridge



Option 3

    When error is indicated


  • turn power switch off so green light is extinguished
  • Hold down resume button and hold down power button so both are held down at same time
  • When green light comes on, continue holding down power button and let resume button go
  • press resume button twice.
  • Let power button go.
  • Press resume button four times, power button should be released before doing this
  • Wait until printer settles down, if power is off, turn on. 
If power will not come on, remove power cord from back of printer, then wait 15 seconds before plugging back in again and turn power on.

2 comments:

  1. AnonymousFebruary 3, 2014 at 2:52 PM

    I got this while doing a cleaning and had the printer open. The problem was not nearly as difficult as described above. I had a bright light on so I could see for cleaning. The light was confusing the sensor! When I turned the light off all worked just as it should.
    Walter

    ReplyDelete
  2. AnonymousAugust 4, 2014 at 12:45 PM

    Thanks so much for your comment, I was going crazy trying to figure out what's happened with my printer while there was a bright light on top of it. Didn't know there was a sensor. Cheers! You saved my day!

    ReplyDelete

Subscribe to: Post Comments (Atom)

Blogger Template created with Artisteer by .